#Cube pro imprimante 3d install
#Cube pro imprimante 3d update
#Cube pro imprimante 3d pro
#Cube pro imprimante 3d professional

#Cube pro imprimante 3d pro

This series of blogs show how we converted this non-working Cube Pro into an amazing printer with open source firmware, high-end components, able to print any materials, and for a fraction of the price of the original printer! The other extruder was still in the printer, but not working anymore. The unit in question had one extruder removed due to malfunction. We found a pretty good deal on a non-working unit and decided to buy it. We knew this printer had excellent mechanical design and we were interested in buying one. For some reasons, it seems like quite a few machines have trouble working properly. Looking at Amazon review, you’ll find that 47% rated 5 stars, and 53% rated 1 star.

#Cube pro imprimante 3d professional

Some stores still have it, or professional users are selling them.Ĥ years after its release, the Cube Pro is in a gray zone.

This printer is not produced anymore, but it’s very common to come across a deal. It was released in 2014 in 3 different versions from 1 to 3 extruders. The Cube Pro is a well-known printer from 3D Systems. DyzeXtruder-GT / DyzeXtruder Pro ENP Liquid Cooling Block.DyzEnd-X/DyzEnd Pro ENP Liquid Cooling Block.Kit DyzEND Pro + DyzeXtruder Pro 1.75mm.

#Cube pro imprimante 3d update

I haven’t tried printing ABS with this machine, to see the efficiency of the box, I’ll update the article if I get the chance, but to be honest I rarely print ABS.įor TPU printing, I just received a spool, so I should be able to test soon, and see how this direct drive extruder handles flexible filament. The printing area is smaller than a CR-10, too bad I would have appreciated a 300×300 plate on this machine. This Sermoon D1 is much quieter than the other Creality machines I have tested so far, especially with the ventilation, which is really nice, you can work next to this machine in complete peaceĪs far as print quality is concerned, nothing to say, it does a very good job, with 3-4 different brands of filaments, and almost 150 hours of printing for this test, I did not encounter any major problems. I really like the design of this machine, it seems very robust, it will be complicated to move, the machine being imposing and heavy. To conclude and give my opinion on the Creality Sermoon D1 Don’t panic, you can start from a generic profile (for a CR-10 for example) by modifying the size of the plate, and also by adjusting the retraction, 1mm will be enough for this Sermoon D1 in direct drive Prusa Slicer configuration for the Sermoon D1Ĭoncerning the slicer, you can use the slicer of your choice, for the moment it will be difficult to find a pre-configured profile, on Cura for example, as the machine has not yet been integrated in the list. I could see during this impression that this machine is quiet, much quieter (ventilation wise) than other older Creality machines I tested so far, which is really nice Here we go… and here is the first print with the Sermoon D1, in the process of being finalized, it’s a “torture test” allowing me to test different print settings, the rendering is really clean.

Once the tray is set, and other checks done, it’s time to start the first print! I strongly recommend printing a test model on the SD card supplied with the printer. The adjustment of the plate is done with an A4 sheet, after having launched an auto-home, it will be necessary to check the distance between the nozzle and the plate at the 4 corners of the plate, as well as in the centre, this adjustment will be done using the wheels present under the plate. Once assembled, this machine really looks good! I really like the design with a very nice finish.īefore launching the first print, it will be necessary to check the set of eccentrics, the tension of the belts and to adjust the plate, this machine is not equipped with a self-levelling sensor.

#Cube pro imprimante 3d install

Given the size of this machine, it is not pre-assembled.įor the assembly, count 30-45min, nothing very complicated, a few screws and some covers, the longest part will be to fix the walls! (which I didn’t install right away for my first tests). When unpacked, the components of the structure look very good, it gives the impression of a high quality machine. The Sermoon D1’s box is imposing, and quite heavy, the package weighs over 26kg! On paper this printer is quite interesting, its structure should allow fast printing, and its walls allow the printing of certain types of filament such as ABS. – Cube structure, with transparent acrylic wallĭespite the cube shape of this machine, it is not a CoreXY, but a Cartesian, if you are looking for a CoreXY printer you will have to look at the Ender 6.